Líderes

test edl xiaomi readmi 5a prime

test edl xiaomi readmi 2

test edl xiaomi mi 5s plus

test edl xiaomi mi max 2

Posta Apenas Test Point EDL Xiaomi

xiaomi mi note 2 100% feito pela umt Operation : Reset Mi Account Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM8) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...OK Init Handshake Sequence...OK Hardware ID : E1F00500 [8996] 00000000 OPK_DATA : 65D680382C4E0091ED2A1DDCD7EFD99ED328BEBDAD748E5CE177EC5AB6544AE5 Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Firehose Loader...Done Sending Loader [8996_004.ufl]...Done Executing Loader...OK Detecting Chip Type...OK Hardware : MSM8996, UFS, 64 GB LU Count : 6 [0x00DC7800] [0x00000400] [0x00000400] [0x00008000] [0x00114000] [0x00002000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 131072, Sector Size: 4096 Reading Partition Table...OK Reading Device Information...OK Device : Xiaomi Mi Note 2 [msm8996] Software : NRD90M, V9.5.2.0.NADMIFA [Fri Apr 6 01:14:43 CST 2018] Android Ver. : 7.0 Patch Level : 2018-03-01 Resetting Mi Account Data...Done Preparing Data...Done Formatting Userdata...Done When phone is completely ON, connect to Internet and add Mi Account. -------------- INFORMATION -------------- New Firmware may cause hang on logo. In such case, you need to flash phone to recover. Operation : Reset FRP Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM8) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...Ignored Init Handshake Sequence...OK Hardware ID : E1F00500 [8996] 00000000 OPK_DATA : 65D680382C4E0091ED2A1DDCD7EFD99ED328BEBDAD748E5CE177EC5AB6544AE5 Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Firehose Loader...Done Sending Loader [8996_004.ufl]...Done Executing Loader...OK Detecting Chip Type...OK Hardware : MSM8996, UFS, 64 GB LU Count : 6 [0x00DC7800] [0x00000400] [0x00000400] [0x00008000] [0x00114000] [0x00002000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 131072, Sector Size: 4096 Reading Partition Table...OK Reading Device Information...OK Device : Xiaomi Mi Note 2 [msm8996] Software : NRD90M, V9.5.2.0.NADMIFA [Fri Apr 6 01:14:43 CST 2018] Android Ver. : 7.0 Patch Level : 2018-03-01 Resetting FRP Lock.......Done Operation Finished.

xiaomi mi note 2 testado por min

test edl xiaomi readmi 4a

test edl xiaomi 4x

test edl xiaomi 5 plus

test edl xiaomi mi 5

test edl xiaomi readmi 5a

test edl xiaomi note 4

test edl xiaomi mi 6

test edl xiaomi mi A1

Veja aqui a possível solução:

amigo vai ter que ter uma placa morta ou uma do j5 pra trocar o c.i correspondente ao sensor.

Ja tentou esse procedimento ??