xiaomi mi mix (lithium) frp e conta mi
Operation : Reset Mi Account
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM8)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.0.3
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1F00500 [8996] 00000000
OPK_DATA : 65D680382C4E0091ED2A1DDCD7EFD99ED328BEBDAD748E5CE177EC5AB6544AE5
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_004]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : MSM8996, UFS, Unknown
LU Count : 6 [0x03A77800] [0x00000400] [0x00000400] [0x00008000] [0x00114000] [0x00002000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 131072, Sector Size: 4096
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi MIX [msm8996]
Software : OPR1.170623.032, V10.0.1.0.OAHMIFH [Fri Aug 31 17:37:35 CST 2018]
Android Ver. : 8.0.0
Patch Level : 2018-08-01
Resetting Mi Account Data...Done
Preparing Data...Done
Formatting Userdata...Done
When phone is completely ON, connect to Internet and add Mi Account.
-------------- INFORMATION --------------
New Firmware may cause hang on logo.
In such case, you need to flash phone to recover.
Or downgrade firmware and try Reset Mi Account again.
Operation Finished.
QcFire Ver. 3.3
Operation : Reset FRP
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM8)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.0.3
Connecting to phone...OK
Waiting for response...Ignored
Init Handshake Sequence...OK
Hardware ID : E1F00500 [8996] 00000000
OPK_DATA : 65D680382C4E0091ED2A1DDCD7EFD99ED328BEBDAD748E5CE177EC5AB6544AE5
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8996_004]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : MSM8996, UFS, Unknown
LU Count : 6 [0x03A77800] [0x00000400] [0x00000400] [0x00008000] [0x00114000] [0x00002000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 131072, Sector Size: 4096
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi MIX [msm8996]
Software : OPR1.170623.032, V10.0.1.0.OAHMIFH [Fri Aug 31 17:37:35 CST 2018]
Android Ver. : 8.0.0
Patch Level : 2018-08-01
Resetting FRP Lock.......Done
Operation Finished.
QcFire Ver. 3.3