Bruno Santana Postado Setembro 1, 2020 Compartilhar Postado Setembro 1, 2020 (editado) flash e reset frp free pela umt flash Operation : Flash Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM32) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...OK Init Handshake Sequence...OK Hardware ID : E1F00B00 [8937] 00007200 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8937_035]...Done Executing Loader...OK Auth Enabled Device! You need Mi Auth Account to service! Requesting UMT Auth Service (FREE)...OK Detecting Chip Type...OK Hardware : 8937, eMMC, 32 GB LU Count : 1 [0x03A3E000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Writing [sec.dat] -> [sec] ...Done Writing [vbmeta.img] -> [vbmeta] ...Done Writing [vbmeta.img] -> [vbmetabak] ...Done Writing [devcfg.mbn] -> [devcfg] ...Done Writing [devcfg.mbn] -> [devcfgbak] ...Done Writing [dummy.img] -> [apdp] ...Done Writing [dummy.img] -> [msadp] ...Done Writing [sbl1.mbn] -> [sbl1] ...Done Writing [sbl1.mbn] -> [sbl1bak] ...Done Writing [rpm.mbn] -> [rpm] ...Done Writing [rpm.mbn] -> [rpmbak] ...Done Writing [cmnlib_30.mbn] -> [cmnlib] ...Done Writing [cmnlib_30.mbn] -> [cmnlibbak] ...Done Writing [cmnlib64_30.mbn] -> [cmnlib64] ...Done Writing [cmnlib64_30.mbn] -> [cmnlib64bak] ...Done Writing [km4.mbn] -> [keymaster] ...Done Writing [km4.mbn] -> [keymasterbak] ...Done Writing [misc.img] -> [misc] ...Done Writing [emmc_appsboot.mbn] -> [aboot] ...Done Writing [emmc_appsboot.mbn] -> [abootbak] ...Done Writing [tz.mbn] -> [tz] ...Done Writing [tz.mbn] -> [tzbak] ...Done Writing [dtbo.img] -> [dtbo] ...Done Writing [dtbo.img] -> [dtbobak] ...Done Writing [splash.img] -> [splash] ...Done Writing [adspso.bin] -> [dsp] ...Done Writing [adspso.bin] -> [dspbak] ...Done Writing [persist.img] -> [persist] ...Done Writing [mdtp.img] -> [mdtp] ...Done Writing [mdtp.img] -> [mdtpbak] ...Done Writing [boot.img] -> [boot] ...Done Writing [recovery.img] -> [recovery] ...Done Writing [cache.img ] -> [cache]...Done Writing [NON-HLOS.bin] -> [modem] ...Done Writing [system.img ] -> [system]...Done Writing [vendor.img ] -> [vendor]...Done Writing [cust.img ] -> [cust]...Done Writing [userdata.img ] -> [userdata]...Done Writing [gpt_main0.bin] -> [PrimaryGPT] ...Done Writing [gpt_backup0.bin] -> [BackupGPT] ...Done Applying Patches................Done Resetting device...Done Operation Finished. QcFire Ver. 6.0 reset frp Operation : Reset FRP Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM32) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...Ignored Init Handshake Sequence...OK Hardware ID : E1F00B00 [8937] 00007200 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8937_035]...Done Executing Loader...OK Auth Enabled Device! You need Mi Auth Account to service! Requesting UMT Auth Service (FREE)...OK Detecting Chip Type...OK Hardware : 8937, eMMC, 32 GB LU Count : 1 [0x03A3E000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : Xiaomi Redmi 8 [olive] Brand : Xiaomi Prod.Name : olive Software : ZQL2115-olive-build-20191019025312, V10.3.4.0.PCNMIXM [Sat Oct 19 02:55:28 CST 2019] Android Ver. : 9 Patch Level : 2019-09-01 Resetting FRP Lock......Done Operation Finished. QcFire Ver. 6.0 reset mi acc Operation : Reset Mi Account Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM32) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...Ignored Init Handshake Sequence...OK Hardware ID : E1F00B00 [8937] 00007200 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8937_035]...Done Executing Loader...OK Auth Enabled Device! You need Mi Auth Account to service! Requesting UMT Auth Service (FREE)...OK Detecting Chip Type...OK Hardware : 8937, eMMC, 32 GB LU Count : 1 [0x03A3E000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : Xiaomi Redmi 8 [olive] Brand : Xiaomi Prod.Name : olive Software : ZQL2115-olive-build-20191019025312, V10.3.4.0.PCNMIXM [Sat Oct 19 02:55:28 CST 2019] Android Ver. : 9 Patch Level : 2019-09-01 Resetting Mi Account Data...Done Preparing Data...Done Formatting Userdata...Done When phone is completely ON, connect to Internet and add Mi Account. -------------- INFORMATION -------------- New Firmware may cause hang on logo. In such case, you need to flash phone to recover. Or downgrade firmware and try Reset Mi Account again. Operation Finished. QcFire Ver. 6.0 Editado Setembro 1, 2020 por Bruno Santana Cleyton Moreira reagiu a isso 1 Citar Link para o comentário Compartilhar em outros sites More sharing options...
Jay PI Postado Setembro 1, 2020 Compartilhar Postado Setembro 1, 2020 9 horas atrás, Bruno Santana disse: flash e reset frp free pela umt flash Operation : Flash Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM32) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...OK Init Handshake Sequence...OK Hardware ID : E1F00B00 [8937] 00007200 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8937_035]...Done Executing Loader...OK Auth Enabled Device! You need Mi Auth Account to service! Requesting UMT Auth Service (FREE)...OK Detecting Chip Type...OK Hardware : 8937, eMMC, 32 GB LU Count : 1 [0x03A3E000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Writing [sec.dat] -> [sec] ...Done Writing [vbmeta.img] -> [vbmeta] ...Done Writing [vbmeta.img] -> [vbmetabak] ...Done Writing [devcfg.mbn] -> [devcfg] ...Done Writing [devcfg.mbn] -> [devcfgbak] ...Done Writing [dummy.img] -> [apdp] ...Done Writing [dummy.img] -> [msadp] ...Done Writing [sbl1.mbn] -> [sbl1] ...Done Writing [sbl1.mbn] -> [sbl1bak] ...Done Writing [rpm.mbn] -> [rpm] ...Done Writing [rpm.mbn] -> [rpmbak] ...Done Writing [cmnlib_30.mbn] -> [cmnlib] ...Done Writing [cmnlib_30.mbn] -> [cmnlibbak] ...Done Writing [cmnlib64_30.mbn] -> [cmnlib64] ...Done Writing [cmnlib64_30.mbn] -> [cmnlib64bak] ...Done Writing [km4.mbn] -> [keymaster] ...Done Writing [km4.mbn] -> [keymasterbak] ...Done Writing [misc.img] -> [misc] ...Done Writing [emmc_appsboot.mbn] -> [aboot] ...Done Writing [emmc_appsboot.mbn] -> [abootbak] ...Done Writing [tz.mbn] -> [tz] ...Done Writing [tz.mbn] -> [tzbak] ...Done Writing [dtbo.img] -> [dtbo] ...Done Writing [dtbo.img] -> [dtbobak] ...Done Writing [splash.img] -> [splash] ...Done Writing [adspso.bin] -> [dsp] ...Done Writing [adspso.bin] -> [dspbak] ...Done Writing [persist.img] -> [persist] ...Done Writing [mdtp.img] -> [mdtp] ...Done Writing [mdtp.img] -> [mdtpbak] ...Done Writing [boot.img] -> [boot] ...Done Writing [recovery.img] -> [recovery] ...Done Writing [cache.img ] -> [cache]...Done Writing [NON-HLOS.bin] -> [modem] ...Done Writing [system.img ] -> [system]...Done Writing [vendor.img ] -> [vendor]...Done Writing [cust.img ] -> [cust]...Done Writing [userdata.img ] -> [userdata]...Done Writing [gpt_main0.bin] -> [PrimaryGPT] ...Done Writing [gpt_backup0.bin] -> [BackupGPT] ...Done Applying Patches................Done Resetting device...Done Operation Finished. QcFire Ver. 6.0 reset frp Operation : Reset FRP Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM32) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...Ignored Init Handshake Sequence...OK Hardware ID : E1F00B00 [8937] 00007200 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8937_035]...Done Executing Loader...OK Auth Enabled Device! You need Mi Auth Account to service! Requesting UMT Auth Service (FREE)...OK Detecting Chip Type...OK Hardware : 8937, eMMC, 32 GB LU Count : 1 [0x03A3E000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : Xiaomi Redmi 8 [olive] Brand : Xiaomi Prod.Name : olive Software : ZQL2115-olive-build-20191019025312, V10.3.4.0.PCNMIXM [Sat Oct 19 02:55:28 CST 2019] Android Ver. : 9 Patch Level : 2019-09-01 Resetting FRP Lock......Done Operation Finished. QcFire Ver. 6.0 reset mi acc Operation : Reset Mi Account Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM32) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...Ignored Init Handshake Sequence...OK Hardware ID : E1F00B00 [8937] 00007200 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8937_035]...Done Executing Loader...OK Auth Enabled Device! You need Mi Auth Account to service! Requesting UMT Auth Service (FREE)...OK Detecting Chip Type...OK Hardware : 8937, eMMC, 32 GB LU Count : 1 [0x03A3E000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : Xiaomi Redmi 8 [olive] Brand : Xiaomi Prod.Name : olive Software : ZQL2115-olive-build-20191019025312, V10.3.4.0.PCNMIXM [Sat Oct 19 02:55:28 CST 2019] Android Ver. : 9 Patch Level : 2019-09-01 Resetting Mi Account Data...Done Preparing Data...Done Formatting Userdata...Done When phone is completely ON, connect to Internet and add Mi Account. -------------- INFORMATION -------------- New Firmware may cause hang on logo. In such case, you need to flash phone to recover. Or downgrade firmware and try Reset Mi Account again. Operation Finished. QcFire Ver. 6.0 Aí sim. Citar Link para o comentário Compartilhar em outros sites More sharing options...
ivotec Postado Setembro 2, 2020 Compartilhar Postado Setembro 2, 2020 9 horas atrás, Bruno Santana disse: flash e reset frp free pela umt flash Operation : Flash Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM32) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...OK Init Handshake Sequence...OK Hardware ID : E1F00B00 [8937] 00007200 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8937_035]...Done Executing Loader...OK Auth Enabled Device! You need Mi Auth Account to service! Requesting UMT Auth Service (FREE)...OK Detecting Chip Type...OK Hardware : 8937, eMMC, 32 GB LU Count : 1 [0x03A3E000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Writing [sec.dat] -> [sec] ...Done Writing [vbmeta.img] -> [vbmeta] ...Done Writing [vbmeta.img] -> [vbmetabak] ...Done Writing [devcfg.mbn] -> [devcfg] ...Done Writing [devcfg.mbn] -> [devcfgbak] ...Done Writing [dummy.img] -> [apdp] ...Done Writing [dummy.img] -> [msadp] ...Done Writing [sbl1.mbn] -> [sbl1] ...Done Writing [sbl1.mbn] -> [sbl1bak] ...Done Writing [rpm.mbn] -> [rpm] ...Done Writing [rpm.mbn] -> [rpmbak] ...Done Writing [cmnlib_30.mbn] -> [cmnlib] ...Done Writing [cmnlib_30.mbn] -> [cmnlibbak] ...Done Writing [cmnlib64_30.mbn] -> [cmnlib64] ...Done Writing [cmnlib64_30.mbn] -> [cmnlib64bak] ...Done Writing [km4.mbn] -> [keymaster] ...Done Writing [km4.mbn] -> [keymasterbak] ...Done Writing [misc.img] -> [misc] ...Done Writing [emmc_appsboot.mbn] -> [aboot] ...Done Writing [emmc_appsboot.mbn] -> [abootbak] ...Done Writing [tz.mbn] -> [tz] ...Done Writing [tz.mbn] -> [tzbak] ...Done Writing [dtbo.img] -> [dtbo] ...Done Writing [dtbo.img] -> [dtbobak] ...Done Writing [splash.img] -> [splash] ...Done Writing [adspso.bin] -> [dsp] ...Done Writing [adspso.bin] -> [dspbak] ...Done Writing [persist.img] -> [persist] ...Done Writing [mdtp.img] -> [mdtp] ...Done Writing [mdtp.img] -> [mdtpbak] ...Done Writing [boot.img] -> [boot] ...Done Writing [recovery.img] -> [recovery] ...Done Writing [cache.img ] -> [cache]...Done Writing [NON-HLOS.bin] -> [modem] ...Done Writing [system.img ] -> [system]...Done Writing [vendor.img ] -> [vendor]...Done Writing [cust.img ] -> [cust]...Done Writing [userdata.img ] -> [userdata]...Done Writing [gpt_main0.bin] -> [PrimaryGPT] ...Done Writing [gpt_backup0.bin] -> [BackupGPT] ...Done Applying Patches................Done Resetting device...Done Operation Finished. QcFire Ver. 6.0 reset frp Operation : Reset FRP Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM32) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...Ignored Init Handshake Sequence...OK Hardware ID : E1F00B00 [8937] 00007200 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8937_035]...Done Executing Loader...OK Auth Enabled Device! You need Mi Auth Account to service! Requesting UMT Auth Service (FREE)...OK Detecting Chip Type...OK Hardware : 8937, eMMC, 32 GB LU Count : 1 [0x03A3E000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : Xiaomi Redmi 8 [olive] Brand : Xiaomi Prod.Name : olive Software : ZQL2115-olive-build-20191019025312, V10.3.4.0.PCNMIXM [Sat Oct 19 02:55:28 CST 2019] Android Ver. : 9 Patch Level : 2019-09-01 Resetting FRP Lock......Done Operation Finished. QcFire Ver. 6.0 reset mi acc Operation : Reset Mi Account Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM32) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...Ignored Init Handshake Sequence...OK Hardware ID : E1F00B00 [8937] 00007200 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8937_035]...Done Executing Loader...OK Auth Enabled Device! You need Mi Auth Account to service! Requesting UMT Auth Service (FREE)...OK Detecting Chip Type...OK Hardware : 8937, eMMC, 32 GB LU Count : 1 [0x03A3E000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : Xiaomi Redmi 8 [olive] Brand : Xiaomi Prod.Name : olive Software : ZQL2115-olive-build-20191019025312, V10.3.4.0.PCNMIXM [Sat Oct 19 02:55:28 CST 2019] Android Ver. : 9 Patch Level : 2019-09-01 Resetting Mi Account Data...Done Preparing Data...Done Formatting Userdata...Done When phone is completely ON, connect to Internet and add Mi Account. -------------- INFORMATION -------------- New Firmware may cause hang on logo. In such case, you need to flash phone to recover. Or downgrade firmware and try Reset Mi Account again. Operation Finished. QcFire Ver. 6.0 Vi agora que teve add na UMT no modulo QC Fire pelo visto funciona, show!!! Citar Link para o comentário Compartilhar em outros sites More sharing options...
martinslucas Postado Dezembro 23, 2020 Compartilhar Postado Dezembro 23, 2020 olá estou com um redmi 8 para desbloqueio eu tenho umt ms nao estou conseguindo Citar Link para o comentário Compartilhar em outros sites More sharing options...
yeye Postado Janeiro 21, 2021 Compartilhar Postado Janeiro 21, 2021 consegui o desbloqueio mas apos colocar no wifi bloqueia novamente mi account Citar Link para o comentário Compartilhar em outros sites More sharing options...
Aldinei Jose Postado Janeiro 21, 2021 Compartilhar Postado Janeiro 21, 2021 se tiver a umt apos o unlock voce precisa fazer o antirelock Citar Link para o comentário Compartilhar em outros sites More sharing options...
Marcelo.Silva. Postado Janeiro 21, 2021 Compartilhar Postado Janeiro 21, 2021 3 horas atrás, Aldinei Jose disse: se tiver a umt apos o unlock voce precisa fazer o antirelock antirelock so funciona ate android 8, android 9 nao funciona antirelock e redmi 8 não tem android 8 Citar Link para o comentário Compartilhar em outros sites More sharing options...
KleberGomes Postado Janeiro 22, 2021 Compartilhar Postado Janeiro 22, 2021 (editado) atrasadao kk Editado Janeiro 22, 2021 por KleberGomes Citar Link para o comentário Compartilhar em outros sites More sharing options...
Cleverton Matias Postado Fevereiro 4, 2021 Compartilhar Postado Fevereiro 4, 2021 Em 21/01/2021 em 12:16, yeye disse: consegui o desbloqueio mas apos colocar no wifi bloqueia novamente mi account Não conecta no Wi-Fi baixa o Drony (VPN) bloqueia as atualizações e o encontrar dispositivos e vai ser feliz! Citar Link para o comentário Compartilhar em outros sites More sharing options...
jhonataspnotri Postado Julho 26, 2021 Compartilhar Postado Julho 26, 2021 galera. boa tarde, estou com redmi 8 olive dual chip, consegui flashear a rom dele com Miracle Xiaomi Tools, resolveu o problema da conta MI, mas agora estou com outros problemas, eu apaguei o Imei e ele nao reconhece o Chip, tbm o MXT nao conecta mais, eu nao tenho nem box nem Dongle eu pode me ajudar?????? Citar Link para o comentário Compartilhar em outros sites More sharing options...
d.l cell Postado Julho 27, 2021 Compartilhar Postado Julho 27, 2021 bom dia a todos, alguem pode ajuda com tutorial de como atualiza 8a com miracle desde ja fico grato. jhonataspnotri reagiu a isso 1 Citar Link para o comentário Compartilhar em outros sites More sharing options...
jhonataspnotri Postado Julho 27, 2021 Compartilhar Postado Julho 27, 2021 estou hoje tentando desbloquear um Redmi 8, estou usando o MXT 1.56 crackeado, consigo passar a rom de boa via EDL mas quero mesmo é desbloquear o BL... posso ajudar... Citar Link para o comentário Compartilhar em outros sites More sharing options...
jhonataspnotri Postado Julho 27, 2021 Compartilhar Postado Julho 27, 2021 galera tenho o Miracle Xiaomi Tools 1.56 pathed, eu deu erase no Imei e flasheei a o MIUI12, alguem tem dicas pra resolver o chip e usar o telefone na boa sem bloquear a conta MI????? Citar Link para o comentário Compartilhar em outros sites More sharing options...
jhonataspnotri Postado Julho 27, 2021 Compartilhar Postado Julho 27, 2021 1 minuto atrás, jhonataspnotri disse: galera tenho o Miracle Xiaomi Tools 1.56 pathed, eu deu erase no Imei e flasheei a o MIUI12, alguem tem dicas pra resolver o chip e usar o telefone na boa sem bloquear a conta MI????? Minha duvida, se eu conseguir alterar o imei1 e imei2 poderei usar o telefone de boa???? Citar Link para o comentário Compartilhar em outros sites More sharing options...
Aldinei Jose Postado Julho 27, 2021 Compartilhar Postado Julho 27, 2021 nos imeis nao se meche senao perde o 1 primeiro e nao volta mais Citar Link para o comentário Compartilhar em outros sites More sharing options...
jhonataspnotri Postado Julho 28, 2021 Compartilhar Postado Julho 28, 2021 15 horas atrás, Aldinei Jose disse: nos imeis nao se meche senao perde o 1 primeiro e nao volta mais E se por o mesmo que tava? Ei tentei alterar mas quando reinicia da brick no sistema algo como nv ram .... o segundo altera de boa sem problemas, alguma dica? Então pra que serve erase imei???? Citar Link para o comentário Compartilhar em outros sites More sharing options...
jhonataspnotri Postado Julho 28, 2021 Compartilhar Postado Julho 28, 2021 Agora, jhonataspnotri disse: E se por o mesmo que tava? Ei tentei alterar mas quando reinicia da brick no sistema algo como nv ram .... o segundo altera de boa sem problemas, alguma dica? Então pra que serve erase imei???? Quando da brick eu consigo recuperar com a opção de wipe security e wipe data no recovery, porem reinicia do zero mas os imei 1 e 2 tbm ficam zerados Citar Link para o comentário Compartilhar em outros sites More sharing options...
jhonataspnotri Postado Julho 28, 2021 Compartilhar Postado Julho 28, 2021 1 minuto atrás, jhonataspnotri disse: Quando da brick eu consigo recuperar com a opção de wipe security e wipe data no recovery, porem reinicia do zero mas os imei 1 e 2 tbm ficam zerados O legal que através do mxt eu consigo fazer downgrade instalar a versão q eu quero mudar coisas direto via edl sem custo algum ... não paguei nada, sem Box e sem Dongle, reparei tbm que outros modelos como o Redmi 7 tem uma opção de Unlock Bootloader, será que uma versão mais recente do MXT tem essa opção para Redmi 8 tbm?????? Citar Link para o comentário Compartilhar em outros sites More sharing options...
Aldinei Jose Postado Julho 29, 2021 Compartilhar Postado Julho 29, 2021 tente passar so o arquivo persist Citar Link para o comentário Compartilhar em outros sites More sharing options...
jhonataspnotri Postado Julho 29, 2021 Compartilhar Postado Julho 29, 2021 1 hora atrás, Aldinei Jose disse: tente passar so o arquivo persist Vou tentar amanhã daí posto o resultado, hj foi dia todo tentando Citar Link para o comentário Compartilhar em outros sites More sharing options...
jhonataspnotri Postado Julho 29, 2021 Compartilhar Postado Julho 29, 2021 16 horas atrás, jhonataspnotri disse: Vou tentar amanhã daí posto o resultado, hj foi dia todo tentando dei write persist e escolhi o backup mais antigo, depois dei um wipe security e agora quando liga bliqueia novamente na conta Mi Citar Link para o comentário Compartilhar em outros sites More sharing options...
jhonataspnotri Postado Julho 29, 2021 Compartilhar Postado Julho 29, 2021 7 minutos atrás, jhonataspnotri disse: dei write persist e escolhi o backup mais antigo, depois dei um wipe security e agora quando liga bliqueia novamente na conta Mi entao repeti a dose e escolhi um persist mais atual, entao desbloqueia novamente e o celular liga normal porem nos dois casos o IMEI nao muda... mais alguma ideia????? Citar Link para o comentário Compartilhar em outros sites More sharing options...
jhonataspnotri Postado Julho 31, 2021 Compartilhar Postado Julho 31, 2021 Em 29/07/2021 em 15:18, jhonataspnotri disse: entao repeti a dose e escolhi um persist mais atual, entao desbloqueia novamente e o celular liga normal porem nos dois casos o IMEI nao muda... mais alguma ideia????? Checking server data.. please wait. Get server data.. Done. Starting.. Opening Port.. COM4 : Qualcomm HS-USB MDM Diagnostics 90B8 (COM4) Compile : Dec 12 2020 00:46:36 Release : Nov 18 2020 04:00:00 Hw Ver : sdm439.g Esn : 80A9CF0A Build : N/A Bt : N/A wifi : 60AB67505684 code : 0000 imei : 867195046413324 imei 2 : 868396046303569 Imei 2 Read-only Failed to Write... Imei 2 Write Successfull... Imei Repair ok .. Rebooting Phone.. Process Done.. !!!!!!!!!!!!!O maximo que consegui ate agora mas quando reinicia o NV data fica corrompido e trava na tela do recovery!!!!!!!!!!!!!! Citar Link para o comentário Compartilhar em outros sites More sharing options...
Rmanin Postado Março 6, 2023 Compartilhar Postado Março 6, 2023 boa tarde amigo tem como vc pode me da uma ajuda ai e pq to com um redmi 8 bkicado e tenho a umt ativada emmc mais nao to sabendo qual adapitador usa Citar Link para o comentário Compartilhar em outros sites More sharing options...
Posts Recomendados
Participe da conversa
Você pode postar agora e se cadastrar mais tarde. Se você tem uma conta, faça o login para postar com sua conta.
Nota: Sua postagem exigirá aprovação do moderador antes de ficar visível.