Postado Setembro 1, 2020 4 anos flash e reset frp free pela umt flash Operation : Flash Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM32) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...OK Init Handshake Sequence...OK Hardware ID : E1F00B00 [8937] 00007200 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8937_035]...Done Executing Loader...OK Auth Enabled Device! You need Mi Auth Account to service! Requesting UMT Auth Service (FREE)...OK Detecting Chip Type...OK Hardware : 8937, eMMC, 32 GB LU Count : 1 [0x03A3E000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Writing [sec.dat] -> [sec] ...Done Writing [vbmeta.img] -> [vbmeta] ...Done Writing [vbmeta.img] -> [vbmetabak] ...Done Writing [devcfg.mbn] -> [devcfg] ...Done Writing [devcfg.mbn] -> [devcfgbak] ...Done Writing [dummy.img] -> [apdp] ...Done Writing [dummy.img] -> [msadp] ...Done Writing [sbl1.mbn] -> [sbl1] ...Done Writing [sbl1.mbn] -> [sbl1bak] ...Done Writing [rpm.mbn] -> [rpm] ...Done Writing [rpm.mbn] -> [rpmbak] ...Done Writing [cmnlib_30.mbn] -> [cmnlib] ...Done Writing [cmnlib_30.mbn] -> [cmnlibbak] ...Done Writing [cmnlib64_30.mbn] -> [cmnlib64] ...Done Writing [cmnlib64_30.mbn] -> [cmnlib64bak] ...Done Writing [km4.mbn] -> [keymaster] ...Done Writing [km4.mbn] -> [keymasterbak] ...Done Writing [misc.img] -> [misc] ...Done Writing [emmc_appsboot.mbn] -> [aboot] ...Done Writing [emmc_appsboot.mbn] -> [abootbak] ...Done Writing [tz.mbn] -> [tz] ...Done Writing [tz.mbn] -> [tzbak] ...Done Writing [dtbo.img] -> [dtbo] ...Done Writing [dtbo.img] -> [dtbobak] ...Done Writing [splash.img] -> [splash] ...Done Writing [adspso.bin] -> [dsp] ...Done Writing [adspso.bin] -> [dspbak] ...Done Writing [persist.img] -> [persist] ...Done Writing [mdtp.img] -> [mdtp] ...Done Writing [mdtp.img] -> [mdtpbak] ...Done Writing [boot.img] -> [boot] ...Done Writing [recovery.img] -> [recovery] ...Done Writing [cache.img ] -> [cache]...Done Writing [NON-HLOS.bin] -> [modem] ...Done Writing [system.img ] -> [system]...Done Writing [vendor.img ] -> [vendor]...Done Writing [cust.img ] -> [cust]...Done Writing [userdata.img ] -> [userdata]...Done Writing [gpt_main0.bin] -> [PrimaryGPT] ...Done Writing [gpt_backup0.bin] -> [BackupGPT] ...Done Applying Patches................Done Resetting device...Done Operation Finished. QcFire Ver. 6.0 reset frp Operation : Reset FRP Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM32) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...Ignored Init Handshake Sequence...OK Hardware ID : E1F00B00 [8937] 00007200 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8937_035]...Done Executing Loader...OK Auth Enabled Device! You need Mi Auth Account to service! Requesting UMT Auth Service (FREE)...OK Detecting Chip Type...OK Hardware : 8937, eMMC, 32 GB LU Count : 1 [0x03A3E000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : Xiaomi Redmi 8 [olive] Brand : Xiaomi Prod.Name : olive Software : ZQL2115-olive-build-20191019025312, V10.3.4.0.PCNMIXM [Sat Oct 19 02:55:28 CST 2019] Android Ver. : 9 Patch Level : 2019-09-01 Resetting FRP Lock......Done Operation Finished. QcFire Ver. 6.0 reset mi acc Operation : Reset Mi Account Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM32) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...Ignored Init Handshake Sequence...OK Hardware ID : E1F00B00 [8937] 00007200 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8937_035]...Done Executing Loader...OK Auth Enabled Device! You need Mi Auth Account to service! Requesting UMT Auth Service (FREE)...OK Detecting Chip Type...OK Hardware : 8937, eMMC, 32 GB LU Count : 1 [0x03A3E000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : Xiaomi Redmi 8 [olive] Brand : Xiaomi Prod.Name : olive Software : ZQL2115-olive-build-20191019025312, V10.3.4.0.PCNMIXM [Sat Oct 19 02:55:28 CST 2019] Android Ver. : 9 Patch Level : 2019-09-01 Resetting Mi Account Data...Done Preparing Data...Done Formatting Userdata...Done When phone is completely ON, connect to Internet and add Mi Account. -------------- INFORMATION -------------- New Firmware may cause hang on logo. In such case, you need to flash phone to recover. Or downgrade firmware and try Reset Mi Account again. Operation Finished. QcFire Ver. 6.0 Editado Setembro 1, 2020 4 anos por Bruno Santana
Postado Setembro 1, 2020 4 anos Em 01/09/2020 em 14:13, Bruno Santana disse: flash e reset frp free pela umt flash Operation : Flash Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM32) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...OK Init Handshake Sequence...OK Hardware ID : E1F00B00 [8937] 00007200 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8937_035]...Done Executing Loader...OK Auth Enabled Device! You need Mi Auth Account to service! Requesting UMT Auth Service (FREE)...OK Detecting Chip Type...OK Hardware : 8937, eMMC, 32 GB LU Count : 1 [0x03A3E000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Writing [sec.dat] -> [sec] ...Done Writing [vbmeta.img] -> [vbmeta] ...Done Writing [vbmeta.img] -> [vbmetabak] ...Done Writing [devcfg.mbn] -> [devcfg] ...Done Writing [devcfg.mbn] -> [devcfgbak] ...Done Writing [dummy.img] -> [apdp] ...Done Writing [dummy.img] -> [msadp] ...Done Writing [sbl1.mbn] -> [sbl1] ...Done Writing [sbl1.mbn] -> [sbl1bak] ...Done Writing [rpm.mbn] -> [rpm] ...Done Writing [rpm.mbn] -> [rpmbak] ...Done Writing [cmnlib_30.mbn] -> [cmnlib] ...Done Writing [cmnlib_30.mbn] -> [cmnlibbak] ...Done Writing [cmnlib64_30.mbn] -> [cmnlib64] ...Done Writing [cmnlib64_30.mbn] -> [cmnlib64bak] ...Done Writing [km4.mbn] -> [keymaster] ...Done Writing [km4.mbn] -> [keymasterbak] ...Done Writing [misc.img] -> [misc] ...Done Writing [emmc_appsboot.mbn] -> [aboot] ...Done Writing [emmc_appsboot.mbn] -> [abootbak] ...Done Writing [tz.mbn] -> [tz] ...Done Writing [tz.mbn] -> [tzbak] ...Done Writing [dtbo.img] -> [dtbo] ...Done Writing [dtbo.img] -> [dtbobak] ...Done Writing [splash.img] -> [splash] ...Done Writing [adspso.bin] -> [dsp] ...Done Writing [adspso.bin] -> [dspbak] ...Done Writing [persist.img] -> [persist] ...Done Writing [mdtp.img] -> [mdtp] ...Done Writing [mdtp.img] -> [mdtpbak] ...Done Writing [boot.img] -> [boot] ...Done Writing [recovery.img] -> [recovery] ...Done Writing [cache.img ] -> [cache]...Done Writing [NON-HLOS.bin] -> [modem] ...Done Writing [system.img ] -> [system]...Done Writing [vendor.img ] -> [vendor]...Done Writing [cust.img ] -> [cust]...Done Writing [userdata.img ] -> [userdata]...Done Writing [gpt_main0.bin] -> [PrimaryGPT] ...Done Writing [gpt_backup0.bin] -> [BackupGPT] ...Done Applying Patches................Done Resetting device...Done Operation Finished. QcFire Ver. 6.0 reset frp Operation : Reset FRP Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM32) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...Ignored Init Handshake Sequence...OK Hardware ID : E1F00B00 [8937] 00007200 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8937_035]...Done Executing Loader...OK Auth Enabled Device! You need Mi Auth Account to service! Requesting UMT Auth Service (FREE)...OK Detecting Chip Type...OK Hardware : 8937, eMMC, 32 GB LU Count : 1 [0x03A3E000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : Xiaomi Redmi 8 [olive] Brand : Xiaomi Prod.Name : olive Software : ZQL2115-olive-build-20191019025312, V10.3.4.0.PCNMIXM [Sat Oct 19 02:55:28 CST 2019] Android Ver. : 9 Patch Level : 2019-09-01 Resetting FRP Lock......Done Operation Finished. QcFire Ver. 6.0 reset mi acc Operation : Reset Mi Account Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM32) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...Ignored Init Handshake Sequence...OK Hardware ID : E1F00B00 [8937] 00007200 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8937_035]...Done Executing Loader...OK Auth Enabled Device! You need Mi Auth Account to service! Requesting UMT Auth Service (FREE)...OK Detecting Chip Type...OK Hardware : 8937, eMMC, 32 GB LU Count : 1 [0x03A3E000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : Xiaomi Redmi 8 [olive] Brand : Xiaomi Prod.Name : olive Software : ZQL2115-olive-build-20191019025312, V10.3.4.0.PCNMIXM [Sat Oct 19 02:55:28 CST 2019] Android Ver. : 9 Patch Level : 2019-09-01 Resetting Mi Account Data...Done Preparing Data...Done Formatting Userdata...Done When phone is completely ON, connect to Internet and add Mi Account. -------------- INFORMATION -------------- New Firmware may cause hang on logo. In such case, you need to flash phone to recover. Or downgrade firmware and try Reset Mi Account again. Operation Finished. QcFire Ver. 6.0 Aí sim.
Postado Setembro 2, 2020 4 anos Em 01/09/2020 em 14:13, Bruno Santana disse: flash e reset frp free pela umt flash Operation : Flash Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM32) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...OK Init Handshake Sequence...OK Hardware ID : E1F00B00 [8937] 00007200 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8937_035]...Done Executing Loader...OK Auth Enabled Device! You need Mi Auth Account to service! Requesting UMT Auth Service (FREE)...OK Detecting Chip Type...OK Hardware : 8937, eMMC, 32 GB LU Count : 1 [0x03A3E000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Writing [sec.dat] -> [sec] ...Done Writing [vbmeta.img] -> [vbmeta] ...Done Writing [vbmeta.img] -> [vbmetabak] ...Done Writing [devcfg.mbn] -> [devcfg] ...Done Writing [devcfg.mbn] -> [devcfgbak] ...Done Writing [dummy.img] -> [apdp] ...Done Writing [dummy.img] -> [msadp] ...Done Writing [sbl1.mbn] -> [sbl1] ...Done Writing [sbl1.mbn] -> [sbl1bak] ...Done Writing [rpm.mbn] -> [rpm] ...Done Writing [rpm.mbn] -> [rpmbak] ...Done Writing [cmnlib_30.mbn] -> [cmnlib] ...Done Writing [cmnlib_30.mbn] -> [cmnlibbak] ...Done Writing [cmnlib64_30.mbn] -> [cmnlib64] ...Done Writing [cmnlib64_30.mbn] -> [cmnlib64bak] ...Done Writing [km4.mbn] -> [keymaster] ...Done Writing [km4.mbn] -> [keymasterbak] ...Done Writing [misc.img] -> [misc] ...Done Writing [emmc_appsboot.mbn] -> [aboot] ...Done Writing [emmc_appsboot.mbn] -> [abootbak] ...Done Writing [tz.mbn] -> [tz] ...Done Writing [tz.mbn] -> [tzbak] ...Done Writing [dtbo.img] -> [dtbo] ...Done Writing [dtbo.img] -> [dtbobak] ...Done Writing [splash.img] -> [splash] ...Done Writing [adspso.bin] -> [dsp] ...Done Writing [adspso.bin] -> [dspbak] ...Done Writing [persist.img] -> [persist] ...Done Writing [mdtp.img] -> [mdtp] ...Done Writing [mdtp.img] -> [mdtpbak] ...Done Writing [boot.img] -> [boot] ...Done Writing [recovery.img] -> [recovery] ...Done Writing [cache.img ] -> [cache]...Done Writing [NON-HLOS.bin] -> [modem] ...Done Writing [system.img ] -> [system]...Done Writing [vendor.img ] -> [vendor]...Done Writing [cust.img ] -> [cust]...Done Writing [userdata.img ] -> [userdata]...Done Writing [gpt_main0.bin] -> [PrimaryGPT] ...Done Writing [gpt_backup0.bin] -> [BackupGPT] ...Done Applying Patches................Done Resetting device...Done Operation Finished. QcFire Ver. 6.0 reset frp Operation : Reset FRP Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM32) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...Ignored Init Handshake Sequence...OK Hardware ID : E1F00B00 [8937] 00007200 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8937_035]...Done Executing Loader...OK Auth Enabled Device! You need Mi Auth Account to service! Requesting UMT Auth Service (FREE)...OK Detecting Chip Type...OK Hardware : 8937, eMMC, 32 GB LU Count : 1 [0x03A3E000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : Xiaomi Redmi 8 [olive] Brand : Xiaomi Prod.Name : olive Software : ZQL2115-olive-build-20191019025312, V10.3.4.0.PCNMIXM [Sat Oct 19 02:55:28 CST 2019] Android Ver. : 9 Patch Level : 2019-09-01 Resetting FRP Lock......Done Operation Finished. QcFire Ver. 6.0 reset mi acc Operation : Reset Mi Account Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM32) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...Ignored Init Handshake Sequence...OK Hardware ID : E1F00B00 [8937] 00007200 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8937_035]...Done Executing Loader...OK Auth Enabled Device! You need Mi Auth Account to service! Requesting UMT Auth Service (FREE)...OK Detecting Chip Type...OK Hardware : 8937, eMMC, 32 GB LU Count : 1 [0x03A3E000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : Xiaomi Redmi 8 [olive] Brand : Xiaomi Prod.Name : olive Software : ZQL2115-olive-build-20191019025312, V10.3.4.0.PCNMIXM [Sat Oct 19 02:55:28 CST 2019] Android Ver. : 9 Patch Level : 2019-09-01 Resetting Mi Account Data...Done Preparing Data...Done Formatting Userdata...Done When phone is completely ON, connect to Internet and add Mi Account. -------------- INFORMATION -------------- New Firmware may cause hang on logo. In such case, you need to flash phone to recover. Or downgrade firmware and try Reset Mi Account again. Operation Finished. QcFire Ver. 6.0 Vi agora que teve add na UMT no modulo QC Fire pelo visto funciona, show!!!
Postado Dezembro 23, 2020 4 anos olá estou com um redmi 8 para desbloqueio eu tenho umt ms nao estou conseguindo
Postado Janeiro 21, 2021 4 anos consegui o desbloqueio mas apos colocar no wifi bloqueia novamente mi account
Postado Janeiro 21, 2021 4 anos Em 21/01/2021 em 16:49, Aldinei Jose disse: se tiver a umt apos o unlock voce precisa fazer o antirelock antirelock so funciona ate android 8, android 9 nao funciona antirelock e redmi 8 não tem android 8
Postado Fevereiro 4, 2021 4 anos Em 21/01/2021 em 15:16, yeye disse: consegui o desbloqueio mas apos colocar no wifi bloqueia novamente mi account Não conecta no Wi-Fi baixa o Drony (VPN) bloqueia as atualizações e o encontrar dispositivos e vai ser feliz!
Postado Julho 26, 2021 3 anos galera. boa tarde, estou com redmi 8 olive dual chip, consegui flashear a rom dele com Miracle Xiaomi Tools, resolveu o problema da conta MI, mas agora estou com outros problemas, eu apaguei o Imei e ele nao reconhece o Chip, tbm o MXT nao conecta mais, eu nao tenho nem box nem Dongle eu pode me ajudar??????
Postado Julho 27, 2021 3 anos bom dia a todos, alguem pode ajuda com tutorial de como atualiza 8a com miracle desde ja fico grato.
Postado Julho 27, 2021 3 anos estou hoje tentando desbloquear um Redmi 8, estou usando o MXT 1.56 crackeado, consigo passar a rom de boa via EDL mas quero mesmo é desbloquear o BL... posso ajudar...
Postado Julho 27, 2021 3 anos galera tenho o Miracle Xiaomi Tools 1.56 pathed, eu deu erase no Imei e flasheei a o MIUI12, alguem tem dicas pra resolver o chip e usar o telefone na boa sem bloquear a conta MI?????
Postado Julho 27, 2021 3 anos Em 27/07/2021 em 20:57, jhonataspnotri disse: galera tenho o Miracle Xiaomi Tools 1.56 pathed, eu deu erase no Imei e flasheei a o MIUI12, alguem tem dicas pra resolver o chip e usar o telefone na boa sem bloquear a conta MI????? Minha duvida, se eu conseguir alterar o imei1 e imei2 poderei usar o telefone de boa????
Postado Julho 28, 2021 3 anos Em 27/07/2021 em 22:58, Aldinei Jose disse: nos imeis nao se meche senao perde o 1 primeiro e nao volta mais E se por o mesmo que tava? Ei tentei alterar mas quando reinicia da brick no sistema algo como nv ram .... o segundo altera de boa sem problemas, alguma dica? Então pra que serve erase imei????
Postado Julho 28, 2021 3 anos Em 28/07/2021 em 14:54, jhonataspnotri disse: E se por o mesmo que tava? Ei tentei alterar mas quando reinicia da brick no sistema algo como nv ram .... o segundo altera de boa sem problemas, alguma dica? Então pra que serve erase imei???? Quando da brick eu consigo recuperar com a opção de wipe security e wipe data no recovery, porem reinicia do zero mas os imei 1 e 2 tbm ficam zerados
Postado Julho 28, 2021 3 anos Em 28/07/2021 em 14:57, jhonataspnotri disse: Quando da brick eu consigo recuperar com a opção de wipe security e wipe data no recovery, porem reinicia do zero mas os imei 1 e 2 tbm ficam zerados O legal que através do mxt eu consigo fazer downgrade instalar a versão q eu quero mudar coisas direto via edl sem custo algum ... não paguei nada, sem Box e sem Dongle, reparei tbm que outros modelos como o Redmi 7 tem uma opção de Unlock Bootloader, será que uma versão mais recente do MXT tem essa opção para Redmi 8 tbm??????
Postado Julho 29, 2021 3 anos Em 29/07/2021 em 00:31, Aldinei Jose disse: tente passar so o arquivo persist Vou tentar amanhã daí posto o resultado, hj foi dia todo tentando
Postado Julho 29, 2021 3 anos Em 29/07/2021 em 01:37, jhonataspnotri disse: Vou tentar amanhã daí posto o resultado, hj foi dia todo tentando dei write persist e escolhi o backup mais antigo, depois dei um wipe security e agora quando liga bliqueia novamente na conta Mi
Postado Julho 29, 2021 3 anos Em 29/07/2021 em 18:09, jhonataspnotri disse: dei write persist e escolhi o backup mais antigo, depois dei um wipe security e agora quando liga bliqueia novamente na conta Mi entao repeti a dose e escolhi um persist mais atual, entao desbloqueia novamente e o celular liga normal porem nos dois casos o IMEI nao muda... mais alguma ideia?????
Postado Julho 31, 2021 3 anos Em 29/07/2021 em 18:18, jhonataspnotri disse: entao repeti a dose e escolhi um persist mais atual, entao desbloqueia novamente e o celular liga normal porem nos dois casos o IMEI nao muda... mais alguma ideia????? Checking server data.. please wait. Get server data.. Done. Starting.. Opening Port.. COM4 : Qualcomm HS-USB MDM Diagnostics 90B8 (COM4) Compile : Dec 12 2020 00:46:36 Release : Nov 18 2020 04:00:00 Hw Ver : sdm439.g Esn : 80A9CF0A Build : N/A Bt : N/A wifi : 60AB67505684 code : 0000 imei : 867195046413324 imei 2 : 868396046303569 Imei 2 Read-only Failed to Write... Imei 2 Write Successfull... Imei Repair ok .. Rebooting Phone.. Process Done.. !!!!!!!!!!!!!O maximo que consegui ate agora mas quando reinicia o NV data fica corrompido e trava na tela do recovery!!!!!!!!!!!!!!
Postado Março 6, 2023 2 anos boa tarde amigo tem como vc pode me da uma ajuda ai e pq to com um redmi 8 bkicado e tenho a umt ativada emmc mais nao to sabendo qual adapitador usa
Participe da conversa
Você pode postar agora e se cadastrar mais tarde. Se você tem uma conta, faça o login para postar com sua conta.
Nota: Sua postagem exigirá aprovação do moderador antes de ficar visível.