Ary Braga Postado Agosto 13, 2009 Compartilhar Postado Agosto 13, 2009 13-08-2009 Next Bulk Update, RAPU-YAMA supported for FBUS Flash Hello, New BULK UPDATE for Cyclone Box is avaiable, changelog: - Introduced support for FBUS Flashing RAPU YAMA phones (5630, 6700, 6303) - GUI Stability improved ; updated Skins Stack - Fixed Algoboot for BB5 phones in some configurations - SingleLine BB5 Flashing Speed improved (upgraded to 5.5mbits from 4mbits) - BB5 Multi-CRT Write bug fixed (mismatched certs when writing more than 1 certs at one time) - Improved Phone LOCAL/TEST Mode Entry algorithms during unlock and FBUS operatinos - Access Violation in some configurations, when changing BB5 Vpl / Dct4 Vpl Variant/Product - fixed - "Set factory defaults - BB5" are now default unticked after flash (useless in case of BB5 phones) - Repower on boot inverted ; accoring to firmware v1.0.5 , BB5 Phones are now default re-powered on boot - By default - USE DEFAULT PROFILE while unlocking DCT4Plus is unticked - DCT4Plus unlock routines rewritten - patch file is now applied before unlocking - Fixed problems upon unlocking some units of DCT4(plus) phones, when Initial SP Area is corrupted - When SIMLOCK IS NOT ACCEPTED during BB5 RPL Write, software trying to write FBUS part again after FLASHBUS part, so if NPC is corrupted, the SL will be restored anyway - Please don't use "Erase Security" function when writing BB5 PA_SL2 RPL, because SIMLOCK will not be accepted in such case! In order of simlock rebuild, NPC MUST BE CORRECT! - Improved BB5 RPL Write, when HWC can't be written (N96 - example), other certs being written and whole procedure is not being skipped - After sending Simlock and Superdongle data, delay added, so PA_SL can recalculate SP and Recreate 308 if needed (previously it wasn't working all times) - During BB5 Configuration Parse (flash chips, status), now RAM chip is displayed instead of UNKNOWN - DCT4Plus Security Status is now being displayed upon unlock - either TAMPERED or NOT TAMPERED - When DCT4Plus Security is NOT TAMPERED, Cyclone automatically makes Security Backup - When user trying to unlock phone which have protected PM308 Security Block against modification, and there is message "Failed to write Security Block" software is now automaticlly writing back NPC backup - IMEI - Erase Security while writing RPL is now by default disabled - SX4 Bypass during PA_SL2 unlock is now by default disabled - IMEI 1234567890?, and "?" is not valid integer bug fixed - Cyclone Box HW Rev A113 support added - Cyclone Box HW Rev A114 support added - Cyclone Box HW Rev A115 support added Example 5630 RAPU Flashed: Scanning avaiable products... Processing C:\Program Files\Nokia\Phoenix\Products\... Processing C:\Program Files\Common Files\Nokia\DataPackage\Products\... Found 114 products, Filtering BB5 Products - wait... 36 Products left after filtering. Ready. Retrieving Variants for Product RM-431 - wait... 53 Variants Retrieved Processing pre flash tasks... Pre flash tasks finished, continuing... Processing rm431_012.008_prd.core.fpsx (CMT)... Booting RAP... CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102011104 CMT_EM_ASIC_ID: 00000C34 CMT_EM_ASIC_ID: 00000C30 CMT_PUBLIC_ID: 1CE001126A2F0344C02621363B888F748DD36748 CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: 25B977A055BE9B5DEC0C38A2A279C695 CMT_ROM_ID: 3E273BF637BE26FA rm431_012.008_prd.core.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5 RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 0.1.37.1, Algo: BB5 Flashbus Write baud set to 650Kbits Flashbus Read baud set to 98Kbits FlashChip[0,CMT]: 0x00EC004000800121, Samsung, ONENAND FlashContent[0,CMT]: 00000000000000000000000000000000, ONENAND FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit RAPUv11_algo_xsr16.fg, Type: Algorithm, Rev: 0.1.40.0, Algo: XSR 1.6 Flashbus Write baud set to 2.0Mbits Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: 8B5237A1F5B38048C11FB4A6B04AE1CDD3C480E2 Flashbus Write baud set to 5.0Mbits Sending Certificates... Certificates OK Partitioning... Partitioning OK Started group flash erase EraseArea[0,CMT]: 0x00020000-0x0003FFFF, ONENAND EraseArea[0,CMT]: 0x00060000-0x004DFFFF, ONENAND EraseArea[0,CMT]: 0x008E0000-0x0A87FFFF, ONENAND Erase Partition (CMT) Waiting 320s for erasure finish... Erase taken 0.922s Writing all blocks... Writing CMT ADA Certificate... Writing CMT KEYS Certificate... Writing CMT PRIMAPP Certificate... Writing CMT RAP3NAND Certificate... Writing CMT SOS+PMML Certificate... Writing CMT PASUBTOC Certificate... Writing CMT PAPUBKEYS Certificate... Writing CMT GENIO_INIT Certificate... Writing CMT SOS*UPDAPP Certificate... Writing CMT SOS*DSP0 Certificate... Writing CMT LDSP Certificate... Writing CMT SOS*ISASW Certificate... Writing CMT SOS+CORE Certificate... Writing CMT SOS+ROFS1 Certificate... Programming Status OK! All blocks written OK! Time taken 107.469s Restarting MCU... Processing rm431_012.008_prd.core.fpsx (APE)... Processing rm431_012.008_06.01_Euro3_prd.rofs2.fpsx (CMT)... Booting RAP... CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102011104 CMT_EM_ASIC_ID: 00000C34 CMT_EM_ASIC_ID: 00000C30 CMT_PUBLIC_ID: 1CE001126A2F0344C02621363B888F748DD36748 CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: 25B977A055BE9B5DEC0C38A2A279C695 CMT_ROM_ID: 3E273BF637BE26FA rm431_012.008_06.01_Euro3_prd.rofs2.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5 RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 0.1.37.1, Algo: BB5 Flashbus Write baud set to 650Kbits Flashbus Read baud set to 98Kbits FlashChip[0,CMT]: 0x00EC004000800121, Samsung, ONENAND FlashContent[0,CMT]: 00000000000000000000000000000000, ONENAND FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit RAPUv11_algo_xsr16.fg, Type: Algorithm, Rev: 0.1.40.0, Algo: XSR 1.6 Flashbus Write baud set to 2.0Mbits Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: 8B5237A1F5B38048C11FB4A6B04AE1CDD3C480E2 Flashbus Write baud set to 5.0Mbits Started group flash erase EraseArea[0,CMT]: 0x06480000-0x09A7FFFF, ONENAND Waiting 320s for erasure finish... Erase taken 0.297s Writing all blocks... Writing CMT SOS+ROFS2 Certificate... Programming Status OK! All blocks written OK! Time taken 57.484s Restarting MCU... Processing rm431_012.008_06.01_Euro3_prd.rofs2.fpsx (APE)... Processing rm431_012.008_C03.01_BLUE_prd.rofs3.fpsx (CMT)... Booting RAP... CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102011104 CMT_EM_ASIC_ID: 00000C34 CMT_EM_ASIC_ID: 00000C30 CMT_PUBLIC_ID: 1CE001126A2F0344C02621363B888F748DD36748 CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: 25B977A055BE9B5DEC0C38A2A279C695 CMT_ROM_ID: 3E273BF637BE26FA rm431_012.008_C03.01_BLUE_prd.rofs3.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5 RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 0.1.37.1, Algo: BB5 Flashbus Write baud set to 650Kbits Flashbus Read baud set to 98Kbits FlashChip[0,CMT]: 0x00EC004000800121, Samsung, ONENAND FlashContent[0,CMT]: 00000000000000000000000000000000, ONENAND FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit RAPUv11_algo_xsr16.fg, Type: Algorithm, Rev: 0.1.40.0, Algo: XSR 1.6 Flashbus Write baud set to 2.0Mbits Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: 8B5237A1F5B38048C11FB4A6B04AE1CDD3C480E2 Flashbus Write baud set to 5.0Mbits Started group flash erase EraseArea[0,CMT]: 0x09A80000-0x0A87FFFF, ONENAND Waiting 320s for erasure finish... Erase taken 0.79s Writing all blocks... Writing CMT SOS+ROFS3 Certificate... Programming Status OK! All blocks written OK! Time taken 4.953s Restarting MCU... Processing rm431_012.008_C03.01_BLUE_prd.rofs3.fpsx (APE)... Processing rm431_012.008_U000.000_prd.uda.fpsx (CMT)... Booting RAP... CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102011104 CMT_EM_ASIC_ID: 00000C34 CMT_EM_ASIC_ID: 00000C30 CMT_PUBLIC_ID: 1CE001126A2F0344C02621363B888F748DD36748 CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: 25B977A055BE9B5DEC0C38A2A279C695 CMT_ROM_ID: 3E273BF637BE26FA rm431_012.008_U000.000_prd.uda.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5 RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 0.1.37.1, Algo: BB5 Flashbus Write baud set to 650Kbits Flashbus Read baud set to 98Kbits FlashChip[0,CMT]: 0x00EC004000800121, Samsung, ONENAND FlashContent[0,CMT]: 00000000000000000000000000000000, ONENAND FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit RAPUv11_algo_xsr16.fg, Type: Algorithm, Rev: 0.1.40.0, Algo: XSR 1.6 Flashbus Write baud set to 2.0Mbits Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: 8B5237A1F5B38048C11FB4A6B04AE1CDD3C480E2 Flashbus Write baud set to 5.0Mbits Started group flash erase EraseArea[0,CMT]: 0x0A880000-0x0F63FFFF, ONENAND Waiting 320s for erasure finish... Erase taken 0.421s Writing all blocks... Programming Status OK! All blocks written OK! Time taken 13.688s Restarting MCU... Processing rm431_012.008_U000.000_prd.uda.fpsx (APE)... All images processed OK! Processing post flash tasks... Reading info... MCU Version V ICPR82_09w24.1 MCU Date 15-06-09 Product RM-431 Manufacturer © Nokia IMEI 359350021136722 Mastercode 3226214523 IMEI Spare 3A95530012317602 IMEI SV 3395530012317632F1000000 PSN CKN036964 Product Code 0564244 Basic Product Code 0559784 PSD 0000000000000000 LPSN 0 WLAN MAC 0025CFDD214E APE SW 012.008 APE Variant 012.008012.008.06.01012.008.C03.01 APE Test rm431_2009wk10v0.010 APE HW 256 APE ADSP 256 RETU 34 TAHVO 00 AHNE 11 HW 0417 RFIC |Vapaus_5.1 | ??? DSP ICPR82_09w24_RIO Simlock Server SIMLOCK SERVER Simlock Key 2440700000000000 Simlock Profile 0000000000000000 Simlock Key Cnt 0 Simlock FBUS Cnt 0 Simlock [1,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [1,2] State: OPENED Type: GID Data: FFFF Simlock [1,3] State: OPENED Type: GID Data: FFFF Simlock [1,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [1,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [2,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [2,2] State: OPENED Type: GID Data: FFFF Simlock [2,3] State: OPENED Type: GID Data: FFFF Simlock [2,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [2,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [3,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [3,2] State: OPENED Type: GID Data: FFFF Simlock [3,3] State: OPENED Type: GID Data: FFFF Simlock [3,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [3,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [4,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [4,2] State: OPENED Type: GID Data: FFFF Simlock [4,3] State: OPENED Type: GID Data: FFFF Simlock [4,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [4,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [5,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [5,2] State: OPENED Type: GID Data: FFFF Simlock [5,3] State: OPENED Type: GID Data: FFFF Simlock [5,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [5,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [6,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [6,2] State: OPENED Type: GID Data: FFFF Simlock [6,3] State: OPENED Type: GID Data: FFFF Simlock [6,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [6,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [7,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [7,2] State: OPENED Type: GID Data: FFFF Simlock [7,3] State: OPENED Type: GID Data: FFFF Simlock [7,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [7,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Read info thread finished, continuing... Post flash tasks finished! Flashing successfully finished! Note on flashing RAPU units: make sure you obtained CORRECT FBUS CABLE! UFC No.2 (As we tested) NOT working with RAPU phones, because MBUS line is duplicated. We recommend to use GPG FBUS cables, as we done our tests using their cables. This is BULK UPDATE, that means you need to download EXE file and click INSTALL. All previously released updates (few days before, rapido nck calc, etc) will be applied automaticlly, loaders will be purged too. You need have only installed installer (this one released in May, avaiable in http://www.cyclonebox.com/downloads/...xInstaller.exe) Download new update from: http://rapidshare.com/files/26700287...te13082009.exe Best Regards, Cyclone Team, Stay tuned. Citar Link para o comentário Compartilhar em outros sites More sharing options...
Posts Recomendados
Participe da conversa
Você pode postar agora e se cadastrar mais tarde. Se você tem uma conta, faça o login para postar com sua conta.
Nota: Sua postagem exigirá aprovação do moderador antes de ficar visível.